[ Return to Main Page ] [ Return to Projects Index ] [Doc's Machine & TWB Store] [ Contact Us ] [ The Whiteboard Webcomic ]

[REDACTED]: Developing an all-new [REDACTED] Paintball Gun
Part 3: Building a Functional Mark II Prototype



As I was still very early in the developmental stages, and would likely have to build at least 2 to 3 more prototypes
in order to truly refine the design, I wasn't looking forward to the idea of having to make a series of [REDACTED]
for each version. Fortunately, a year or two earlier I'd had the bright idea of [REDACTED],
and had [REDACTED] laying around. A few minutes with some of the revised numbers
and a bit of time on the mill, and I had a rough-start lower receiver blank for the Mark II.



Combining the data from the 'proof of concept' prototype, and sketching around the
new receiver and [REDACTED] layout, I was able to rough out a [REDACTED] blank,
and start machining the [REDACTED]. The [REDACTED], but I didn't waste too
much time making it pretty since this is still an early prototype.



Again using the new data, and fresh specs from the newly-created [REDACTED],
I was able to do considerable work to the [REDACTED] blank.
 


To match up with that, I painstakingly machined a new upper reciever, taking more time and care in order to
get the two halves to match up snugly and accurately. It may not look like it, but there's probably six to eight
hours machining time in that part up there.



But it was worth it. The two halves fit together almost perfectly, and the new design keeps everything covered
with just the one visible fastener on each side.



As this is intended to be a functional prototype, a [REDACTED] was fabricated and fitted.



And, to retain it, I made this little recessed tie-bar, which both retains the [REDACTED],
and helps stabilize where the two receiver halves come together. In the next version this tab
will be made integral to the lower reciever.



Now we're getting past where we were with the Mark I prototype, and I had to figure out how to slip a trigger
into the assembly. While this one works, it took far too much "cobbling", and I'm not terribly happy with it.
A little more thought will be necessary for the Mark III version.



And now we're getting somewhere. I have, of course, skipped a lot of steps, as this article isn't necessarily
intended to be a blow-by-blow how-it's-done. It's mainly documenting the steps necessary to go from an
idea on paper, to a functional prototype, and if we're lucky, into limited production.

Here, the reciever is shown almost complete. As noted earlier, we're using some [REDACTED],
since there's no need to reinvent the wheel, as they say. The bolt is complete and fitted with a [REDACTED],
the trigger is in place and has a small pin to retain it (small spot just below the [REDACTED]) the body has been
tapped for an air fitting [REDACTED] and I'm using a lightweight spring for testing.



As the air passage took the place of the [REDACTED], I added a short pipe nipple to the receiver,
and fabbed up this aluminum insert which screws to the nipple and acts like a [REDACTED]. The
insert is drilled through and accepts a QD nipple, so the gun can be tested with a remote hose.



And, the finishing touch- at least, for the moment- I whipped up a proper [REDACTED], since the [REDACTED]
[REDACTED] is just a [REDACTED] for now. This [REDACTED] will help lock it in place for testing.



November 20th, 2016: There it is, a fully-functioning prototype (minus the [REDACTED], at the moment)
built almost entirely from scratch, going from cocktail-napkin drawings to a working second-generation
model in just 20 days.

But, we're just getting started...





All text, photos and graphics Copyright 1998- 2017, Doc's Machine & Airsmith Services. All Rights Reserved.
Information contained in these pages is for reference and entertainment purposes only.  Our methods are not always the best,
quickest, safest, or even the correct ones. It's up to you to know how to use your own machines and tools.
Keep your fingers away from the spinny blades o' death and you should be all right.